WINGS AND WHEELS Soaring Supplies
2049 Shadyside Road
Lakewood, NY 14750
Telephone (716)763-3213 Fax (716)763-3214
email: tim@wingsandwheels.com

OXYGEN EQUIPMENT
continued from previous page
Typically used connector types
for your information

We can supply the most common type connectors, not all of the above pictured types will be available from stock but may be from special order. We do stock CPC in Metal or Nylon, Puritan 750, MS (Military) and Aerox connectors and some of the female fittings for the same types.
Please note: Many aircraft have systems installed that provide a fixed flow at the user outlet with little of no reduction in the pressures from the regulator. These systems use connector with tiny orifices as the final reduction in pressure to a usable level for breathing with a mask that provides oxygen levels based on the service ceilings of the aircraft type. With this setting and orifice installed the system provides excess (loss or wasted oxygen) at lower altitudes but provides adequate oxygen levels for the maximum altitude the aircraft might obtain. Having too much oxygen isn't especially dangerous but can cause headaches, excessive dehydration and drying and leave users some discomfort. Because of this you we cannot use simple connectors without having the proper orifice installed to reduce the flow. We can supply some types with the orifice for a fixed altitude but must know the aircraft type. A better and far more efficient system, the Aerox retrofit kits with adjustable needle valves and flowmeters allows the use of the more comfortable and preferred Cannulas or the use of conventional masks and also reduced oxygen wasted by fixed systems.
BASIC AEROX RETROFIT KIT
The Aerox Retrofit Kit consists of three parts

Newest type RK-202 shown on right with included in-line adjustable Glo-meter"

• Oxysaver Cannula--this comfortable device may be used in place of a mask at altitudes up to 18,000 feet MSL. It has a conserving feature that can extend your oxygen supply up to eight times.

• Aerox Flowmeter/Indicator-(Replaced now by Aerox Glo-Meter - this device not only indicates oxygen flow but also reads directly in thousands of feet MSL. Aerox Glo-Meter /Indicator has dual scale--useable for Oxysaver Cannulas or masks.

• Aerox Adjustable Flow Valve--an all metal, thumb screw operated needle valve allows you to precisely control flow. The adjustable needle valve is attached to the outlet end of the connector supplied with your system. Flow can now be controlled precisely for altitude and type of equipment (Oxysaver cannula, mask or regular cannula). The flowmeter and needle valve may also be co-located. (See photo of Aerox flowmeter and needle valve combo below.)

  • Glo-Meter/Needle valve Also available as a combination Glow-meter with Needle valve as an integral unit.

RETROFIT CONNECTORS
CONNECTORS AND COMMON FITTINGS SHOWN WITH AEROX NEEDLE VALVE
 

RK-202		Retofit Kit For Aerox 350 & 400 Series Regulators (Fits Newer Aerox Portable Systems)	$93.00*
RK-MK-1		Retrofit Kit For Medical Regulator With Fittings For 1 User	$89.00*
RK-MK-2		Retrofit Kit For Medical Regulator With Fittings For 2 Users	$177.00*
RK-MS		Retrofit Kit With Military Type Fitting	$116.00*
RK-PB-1		Retrofit Kit With Puritan Bennett Type (New Style) Fittings. Fits Newer Aerox Built-in Systems.	$108.00*
RK-PB-2		Retrofit Kit With Puritan Bennett Type (Old Style) Fittings	$108.00*
RK-SC		Retrofit Kit With Scott Type Fitting	$108.00*
RK-SK		Retrofit Kit With Sky-Ox Type Fitting.	$116.00*

*Retrofit kits include: FM and connector/needle vale or FMNV flow meter, combination  needle valve/flow meter with separate connector and Oxysaver Cannula (Can You La)



CPC Ryan nylon coupling body for regulator.........$19.95
CPC Ryan coupling insert (Nylon).....................$3.95
CPC Ryan coupling insert (metal)...........$11.95

Aerox Brass Outlet and Male connector


Aerox  Barb........$3.00
Aerox 201 Barb insert connector $3.50
 Aerox 202 Plug with 10/32 Female thread $4.00
Aerox 203 Outlet fitting......$16.00

Please note the connectors below cannot simply be used in most aircraft with the mating outlets
without the addition of either a restrictor specific to the aircraft type, one of our retrofit kits or a flowmeter and
needle valve. Generally, most aircraft oxygen systems have fixed outlet pressures to deliver the minimum
flow rate required to match the aircraft service ceiling when used with the specific restrictor placed in the
connector to limit the flow rate to a usable level.

Aerox Puritan Bennett PB-1A connector with tube barb $44.95

 PB-2 connector (with Aerox barb installed for use with 1/8" oxygen tube)
** Connectors do not include a restrictor orifice specific to aircraft type
For these please see retrofit kits above
$44.95

MS connector and socket as used on older A-8-A's like above...(not outlet is not now available)
MS (military) connector  with Aerox barb installed for use with 1/8" oxygen tube
** Connectors do not include a restrictor orifice specific to aircraft type
For these please see retrofit kits above
MS Fitting with Barb........$44.95

Scott Connector with Aerox barb installed for use with 1/8" oxygen tube
** Connectors do not include a restrictor orifice specific to aircraft type
For these please see retrofit kits above
$44.95

Example

Scott connector with Aerox Needle valve as used in retrofit kits

** Connectors may require restrictor orifice specific to aircraft type unless used with a regulating needle valve and flowmeter. For these please see retrofit kits above

SPECIAL AEROX
Puritan Bennett Panel mount outlet adapter

As show, (but not including Male Aerox PB-1 connector)
May be mounted to panel with mount ring and washer (removed in left image) or by 2 small 8/32 screws in top of base
has as standard, 1/4 NPT fitting or can be reduced to 1/8 NPT swage-lock fitting
$95.00


In-Line quick-disconnects for switching between mask and cannula*$5.95pr.
*not necessary with Aerox flowmeter and masks/cannulas

Filling adapters
Precautions must be taken when refilling any system
but with this in mind we can offer adapters suitable for most application.

Aerox PB (Schreder) In-line fill valve...$24.95
Aerox PB (Schreder) In-line fill valve  with cap and safety chain...$34.95

Filling stations and adapters
FBO-1  Cascade Cylinder Filling System

Note system is shown with "optional" High Pressure Regulator in place of reducing orifice
Tandem connections with 0 to 4000 PSI Gauge on 6 foot braided stainless steel hose
 with 540 filler for portable applications,
Scott filling adapter,  Puritan Bennet filling adapter, reducing orifice
$440.00 with reducing orifice but without  High Pressure Regulator
$890.00 (recommended) including High Pressure Regulator in place of  reducing orifice

Above: Example only
FBO Cart with Cascade filling system
 (Cylinders and cart sold locally by Oxygen suppliers, welders suppliers and others)

FA540-60
Bottle to Bottle filling hose or extension with 60" Stainless Steel high pressure hose.
does not include restricting orifice or regulator
$169.00


FA540-72-G
Like above includes a high pressure gauge and orifice to reduce the flow rate.
$249.00
Filling Adapters
 CGA (Compressed Gas Association)
 The CGA connection standard numbers are followed by a multipart, sequentially listed descriptive code. This code generally includes:
Outside diameter of valve threads
 Threads per inch and thread size
Left-hand or right-hand thread
External or internal threads

FA-540-90 (540 Female to 540 Female) $54.00

FA-PB3 with 3" extension  $79.00

FA-PB3-90 3" for cylinders with Puritan Bennett valves with 90 degree elbow  $72.00


FAM-PB3  Male 540 to Female PB Filler with 3" extension  $72.00

FA-PBM CGA-540 Female to Puritan-Bennett female fillers.
Universal type filling adapter useful for filling USA 540 type cylinders from many airport FBO's in many countries
$72.00

FAM-BR To fill British cylinders $81.00

 FA-SC Female 540 to Scott filler $72.00
FAM-SC- Male 540 to Scott filler $72.00
FA-870 Filling Adapter  870 to 540 $82.00


FA-870M Filling adapter $74.00

FA-DIN
 
540 to EU DIN $148.00

High Pressure Copper Tubing and fittings
for remote mounting of high pressure gauges and filling adapters

1/8" diameter specially cleaned copper tube for use with O2
Used to remote mount high pressure gauges, Schreder filling adapters ect.
$1.70 per foot

brass fittings are normally in stock in most of the below types, or we can make up combinations from what is available to make up lines for your application from what is here.

Swagelok High pressure copper fittings for 1/8" copper

(1/4 NPT Female / Swagelok Compression fitting, for Brass 1/8" Tube)
$14.00


1/4 NPT Elbow Male/Female
$9.00

"T " fittings

 1/4 NPT Male / Male / Male
 or Female / Male / Female 1/4" NPT High Pressure
$12.00


Swagelok Compression fitting, Brass 1/8"  / Male 1/4 NPT / Swagelok Compression fitting, Brass 1/8"
Swagelok Compression fitting, Brass 1/8"  / Swagelok Compression fitting, Brass 1/8" / Swagelok Compression fitting, Brass 1/8"
fittings for remote mounting gauges, filler valves ect.
$24.50

Sorry.......No longer available here
For over 20 years Nelson Aircraft Company has produced oxygen systems available for general aviation aircraft.
Recently Jerry Nelson sold his company which them became NELSON OXYGEN-PRECISE FLIGHT, in 2006 NELSON OXYGEN-PRECISE FLIGHT took all sales and service of their products in-house.
 W&W Can still supply most compatible system parts and we can offer systems made from parts typically used by Nelson combined with parts form AEROX to make suitable systems for nearly all users.

Please see previous page for additional oxygen systems
and component parts
 

36
  Browse the catalog 
Back to Index